TOOLS for POOL & SPA SERVICE
Available through most distributors.
Aqua Wrench Tools
EB1803  
Eye Ball Seat Removal Tool
                                                                                    
Extra long design reaches deep into fittings
recessed slots and provides & extra leverage. Great
for loosening slotted plugs. Fits 1 ½” slotted wall
fitting (Hayward, Pentair, etc.).     
Cord Stoppers
Q-CS1        ¾” RETROFIT FOR EXISTING 120-VOLT INSTALLATION.
Q-CS2       1” RETROFIT FOR EXISTING 120-VOLT INSTALLATION.
Q-CS3        ¾” NEW 120-VOLT INSTALLATION.
Q-CS4       1” NEW 120-VOLT INSTALLATION.
Q-CS5        ¾” RETROFIT FOR EXISTING 12-VOLT INSTALLATION.
Q-CS6       1” RETROFIT FOR EXISTING 12-VOLT INSTALLATION.
Q-CS7       ¾” NEW 12-VOLT INSTALLATION.
Q-CS8       1” NEW 12-VOLT INSTALLATION.
Q-CS9       1” 2-HOLE RETROFIT FOR BONDING GROUND INSTALLATION.
Q-CS10    1” 2-HOLE BONDING GROUND NEW INSTALLATION.  
Eliminate water leaks at the pool light. Stop wondering if that light niche conduit is
sealed; use Cord Stopper on new installation or old. We have 10 Cord Stoppers to
seal light niches in New Construction or Old Pools! Molded rubber stoppers fit snuggly
around cords to seal the light niche without messy silicone or putty. Retrofit is split to
make below waterline repair on a leaking light easy. Cord Stopper makes light
replacement fast & easy, no silicone or putty to dig out. Minimum order 6 pieces
PT2000     
Polaris/Letro UWF Removal Tool

Notched design allows you to remove pool cleaner
fitting even when lock tabs are broken off. Automatic
pool cleaner wall fitting (Polaris, Letro & Mars-
Barracuda).
HAD4040
Retaining Ring Tool

Designed to grip recessed notch rings on HydroAir
& Hayward or cross-leg over knobs on Waterway &
Pentair rings and loosens even tight fittings.
ADP1500
Duck Plug Wrench

This laser cut steel wrench perfectly fits the
Anderson Winter Duck Plug for easy tightening and
removal. Other wrenches may slip tearing vinyl
liners or damaging other pool surfaces or the plug.
PAC2019
Clean & Clear Drain Plug Tool

Reaches the hard to access drain plug with added
leverage for extra tight plugs. Use for several
Pentair & Sta-Rite filters.
HT2190
Adjustable Spa Jet Tool

Deep forks allow full access to recessed tabs to
fully tighten so adjustable jets come loose again
and you can loosen them when necessary. Use on
any spa jet retaining ring recessed behind jet
(e.g. HydroAir, Jacuzzi, Waterway).
HYD3901
HydroAir 4 Tip Wall Fitting Tool

The metal tips of our tool grip the recessed slots
better than the plastic tool that strips out easily. Fits
HydroAir wall fitting with 4 recessed slots. Use on
HydroAir Slimline, Builder, LoProfile Builder and
Micro Jet Series.
HYD6402
HydroAir 6 Tip Wall Fitting Tool

The metal tips of our tool grip the recessed slots
better than the plastic tool         that strips out
easily. Fits HydroAir wall fitting with 6 recessed
slots. Hydro Jet Series, Standard Wall Fittings and
High Volume Suctions
HYD8402
HydroAir 8 Tip Wall Fitting Tool

The metal tips of our tool grip the recessed slots
better than the plastic tool that strips out easily. Fits
HydroAir wall fitting with 8 recessed slots. Bath
Freedom, Caged Freedom and AF MK II Jet Series
HYD5003     
HydroAir 2 in 1 Jet Face Wrench

This 2 in 1 wrench fits two jet face sizes. The pins
on each end of the wrench fit into the holes to turn
the jet without damaging the fitting Use on Magna,
SL Magna, Super Magna, Coverta’ssage, Micro’
ssage, Butterfly Jet Series and Standard Wall
Fittings with 2 Holes.
HYD9075     
HydroAir Magnaflow Fitting Tool

This tool has a precision fit to make the job easy,
bent two ways to easily access the fitting and a stop
bar to keep it in place. Use on Micro Magna Jet
Series.
HYD9099
HydroAir Directional Eye Nut Wrench

No need to fight those pliers to tighten or loosen
the nut. Use on Micro Adjustable VSR Series
SIR1205   Discontinued use HYD5003
Spa Fitting Removal Tool

Ergonomic handle and design gives the leverage
necessary to removal spa jet face plates with two
recessed holes. Break, twist or strip the holes in the
fitting. Use on several spa jet face plates with two
recessed holes.